콘텐츠로 건너뛰기
Merck
모든 사진(1)

주요 문서

Z264946

Sigma-Aldrich

Aldrich® glass pH electrode

BNC connector

로그인조직 및 계약 가격 보기

크기 선택

1 EA
₩286,636

₩286,636


구입 가능 여부는 고객센터에 문의하십시오.


크기 선택

보기 변경
1 EA
₩286,636

About This Item

UNSPSC 코드:
41115603
NACRES:
NB.79

₩286,636


구입 가능 여부는 고객센터에 문의하십시오.

파라미터

−5-110 °C temperature

유사한 제품을 찾으십니까? 방문 제품 비교 안내

일반 설명

For applications where a separate reference electrode is required. Fast response over the full pH range with low sodium ion error. Useful for highly acidic or highly alkaline samples.

Help in selecting the correct electrode can be viewed at Electrode Selection Guide
Hints on Electrode Maintenance

법적 정보

Aldrich is a registered trademark of Sigma-Aldrich Co. LLC

관련 제품


가장 최신 버전 중 하나를 선택하세요:

시험 성적서(COA)

Lot/Batch Number

It looks like we've run into a problem, but you can still download Certificates of Analysis from our 문서 section.

도움이 필요하시면 연락하세요. 고객 지원 부서

이 제품을 이미 가지고 계십니까?

문서 라이브러리에서 최근에 구매한 제품에 대한 문서를 찾아보세요.

문서 라이브러리 방문

질문

1–2 / 2 질문  
  1. Is the electrode "Z264946" refillable?

    1 답변
    1. Yes, it can be re-filled.

      도움이 되었습니까?

  2. Please provide user guide for Z264946 Aldrich® glass pH electrode.

    1 답변
    1. A user guide is not available for this product. See the usage instructions below:
      PREPARATION FOR USE:
      1. Wet lower end of electrode in tap water. Carefully remove the lower cap.
      NOTE: The cap is used only for shipping and storage. You might want to keep it for later use.
      2. If air bubbles are present in the bulb area, shake downwards to displace any air bubbles in the bulb.
      pH MEASUREMENT:
      1. Thoroughly rinse the electrode tip in distilled water and insert electrode tip in a known buffer, close to the sample to be tested, along with an appropriate reference electrode.
      2. Adjust the ‘standardize’ control on the pH meter until the meter reads the value of the buffer.
      3. Thoroughly rinse the electrodes with distilled water, then insert the electrodes in the solution to be tested.
      NOTE: The electrode tips should be rinsed in distilled water between each measurement to prevent contamination of the next solution.
      STORAGE PROCEDURES:
      1. For short storage (up to one week), the electrode may be placed in a beaker containing approximately 1 inch saturated KCl solution.
      2. For long-term storage (over one week), fill storage cap with KCl solution and place the cap back on the electrode tip.
      The electrode may then be placed back in the box and stored.

      도움이 되었습니까?

후기

평점 값 없음

활성 필터

자사의 과학자팀은 생명 과학, 재료 과학, 화학 합성, 크로마토그래피, 분석 및 기타 많은 영역을 포함한 모든 과학 분야에 경험이 있습니다..

고객지원팀으로 연락바랍니다.