KHVEA03TT3

Millipore Express^® SHRP, Opticap^® XL Capsule

Opticap^® XL 3, inlet connection diam. 1.5 in., pore size 0.5/0.1 μm, cartridge nominal length 3 in. (7.5 cm)

• Synonim(y): Opticap Autoclavable XL 3 Millipore Express SHR with Prefilter 0.5/0.1 μm 1-1/2 in. TC/TC
• Kod UNSPSC: 23151806

Właściwości

• Materiały: polyethersulfone ; polypropylene ; polypropylene housing; polypropylene support; polypropylene vent cap; polysulfone ; silicone seal
• Poziom jakości: 400
• zgodność regionalna: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• sterylność: non-sterile
• Kompatybilność ze sterylizacją: autoclavable compatible
• linia produktu: Opticap^® XL 3
• Właściwości: hydrophilic
• producent / nazwa handlowa: Millipore Express^®
• Parametry: ≤7.2 mL/min air diffusion at 3.45 bar (50 psig) and 23 °C (in water); 1.0 bar max. differential pressure (15 psid) at 80 °C (Forward); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 100 psi max. differential pressure (6.9 bar) (intermittent); 2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent); 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward); 5.5 bar max. inlet pressure (80 psi) at 23 °C; 6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent); 6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent); 80 psi max. differential pressure (5.5 bar) (continuous); 80 psig max. inlet pressure
• metody: sterile filtration: suitable
• Długość: 17.3 cm (6.8 in.)
• Szerokość: 4.2 in.
• długość nominalna kartridża: 3 in. (7.5 cm)
• Średnica: 10.7 cm (4.2 in.)
• powierzchnia filtracyjna: 0.13 m²
• śr. przyłącza doprowadzającego: 1.5 in.
• szer. od złącza doprowadzającego do złącza odprowadzającego: 17.3 cm (6.8 in.)
• śr. przyłącza odprowadzającego: 1.5 in.
• zanieczyszczenia: ≤0.25 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• macierz: Millipore Express^® SHR (w/Prefilter)
• pore size: 0.5/0.1 μm pore size
• punkt pęcherzykowania: ≥2586 mbar (37.5 psig), nitrogen with 70/30% IPA/water at 23 °C
• dopasowywanie: 1/4 in. drain/vent hose barb (with double O-ring Seal); inlet sanitary flange; outlet sanitary flange; (38 mm (1 1/2 in.) Sanitary Flange Inlet and Outlet)

Opis

Opis ogólny

Device Configuration: Capsule

Opakowanie

Double Easy-Open bag

Inne uwagi

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Uwaga dotycząca przygotowania

Sterilization Method
3 autoclave cycles of 60 min @ 126 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Komentarz do analizy

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 5.5 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥2 L

Informacje prawne

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Oświadczenie o zrzeczeniu się odpowiedzialności

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.

This page may contain text that has been machine translated.