Direkt zum Inhalt
Merck

Speciation of phosphorus in the sediments of Lake Bini (Ngaoundere-Cameroon).

Environmental technology (2014-06-25)
Joseph Marie Sieliechi, Jean-Marie Dangwang Dikdim, Guy Bertrand Noumi
ZUSAMMENFASSUNG

In this study, spatial and seasonal variations of phosphorus fractions in Lake Bini sediments were evaluated using a sequential extraction method. The sampling of water and sediments (surface and coring) was carried out at seven sites around the lake during the dry season and the rainy season. The results showed that phosphorus is mainly in the inorganic form (L-P+Ca-P+Fe-P) in the sediments whatever the season may be. The rank order of phosphorus extracts obtained was Fe-P>Ca-P>OM-P>L-P>Res-P. The maximum values of phosphorus (sum of each fraction) were obtained in the rainy season at the sites D6 (298.12 +/- 12.37 microg P/g) and D4 (244.93 +/- 11.06 microg P/g) located beside water source 2 and farmland 2, respectively. The average values of the phosphorus content vary from 05.29 +/- 1.05 microg P/g to 102.58 +/- 4.62 microg P/g for the upper layer (0-5 cm depth); 04.67 +/- 0.66 microg P/g to 70.06 +/- 2.82 microg P/g for the medium layer (5-10 cm depth) and finally 04.63 +/- 0.98 microg P/g to 55.24 +/- 5.17 microg P/g for the deep layer (10-15 cm depth). The results of principal component analysis showed that processes which enhance Ca-P and Fe-P accumulation are probably related to the same factor and the origin of P depends on the source of pollution. The nature of the season plays a significant role in the geochemical composition of the sediments in phosphorus and on the eutrophication level of Lake Bini.

MATERIALIEN
Produktnummer
Marke
Produktbeschreibung

Sigma-Aldrich
Eisen, ≥99%, reduced, powder (fine)
Sigma-Aldrich
Carbonyleisen, ≥97% Fe basis
Sigma-Aldrich
Phosphor, rot, ≥99.99% trace metals basis
Sigma-Aldrich
Eisen, puriss. p.a., carbonyl-Iron powder, low in magnesium and manganese compounds, ≥99.5% (RT)
Sigma-Aldrich
Eisen, powder, −325 mesh, 97%
Sigma-Aldrich
Eisen, granular, 10-40 mesh, >99.99% trace metals basis
Sigma-Aldrich
Eisen, foil, thickness 0.1 mm, ≥99.9% trace metals basis
Sigma-Aldrich
Eisen, chips, 99.98% trace metals basis
Sigma-Aldrich
Eisen, wire, diam. 1.0 mm, ≥99.9% trace metals basis
Sigma-Aldrich
Phosphor, rot, ≥97.0%
Eisen, foil, 100x100mm, thickness 0.25mm, hard, 99.5%
Sigma-Aldrich
Eisen, foil, thickness 0.25 mm, ≥99.99% trace metals basis
Eisen, foil, 300x300mm, thickness 0.1mm, hard, 99.5%
Eisen, foil, 100x100mm, thickness 0.125mm, as rolled, 99.99+%
Eisen, rod, 200mm, diameter 25mm, as drawn, 98+%
Eisen, tube, 200mm, outside diameter 8.0mm, inside diameter 5mm, wall thickness 1.5mm, annealed, 99.5%
Eisen, rod, 100mm, diameter 100mm, as drawn, armcO« soft ingot 99.8%
Eisen, foil, 100x100mm, thickness 1.0mm, as rolled, 99.5%
Eisen, rod, 50mm, diameter 5.0mm, as drawn, 99.99+%
Eisen, foil, 100x100mm, thickness 0.5mm, hard, 99.5%
Eisen, foil, 150x150mm, thickness 1.5mm, as rolled, 99.5%
Eisen, rod, 150mm, diameter 6.0mm, as drawn, 99.99+%
Eisen, rod, 100mm, diameter 2.0mm, as drawn, 99.95%
Eisen, foil, 25x25mm, thickness 0.9mm, as rolled, 99.5%
Eisen, tube, 200mm, outside diameter 5.0mm, inside diameter 4.5mm, wall thickness 0.25mm, as drawn, 99.5%
Eisen, foil, 25x25mm, thickness 1.0mm, as rolled, 99.5%
Eisen, foil, 50x50mm, thickness 0.1mm, hard, 99.5%
Eisen, rod, 200mm, diameter 9.5mm, as drawn, soft ingot 99.8+%
Eisen, rod, 500mm, diameter 4.8mm, as drawn, 98+%
Eisen, foil, 25x25mm, thickness 0.5mm, hard, 99.5%