KHGLA1THH1

Multilayer Durapore^® 0.45/0.22 µm, Opticap^® XLT Capsule

Opticap^® XLT 10, cartridge nominal length 10 in. (25 cm), filter diam. 4.2 in. (10.7 cm)

• UNSPSC-Code: 23151806

Eigenschaften

• Materialien: polypropylene filter; polypropylene housing; polypropylene support; silicone seal
• Qualitätsniveau: 400
• Einhaltung gesetzlicher Vorschriften: FDA 21CFR177-182 (all component materials)
• Sterilität: non-sterile
• Kompatibilität mit Sterilisationsverfahren: autoclavable compatible
• Produktlinie: Opticap^® XLT 10
• Leistungsmerkmale: hydrophilic
• Hersteller/Markenname: Opticap^®
• Parameter: ≤10.8 mL/min air diffusion at 2.75 bar (40 psig) and 23 °C (in water); 1 bar max. inlet pressure (15 psi) at 80 °C; 1.05 bar max. differential pressure (15 psid) at 80 °C (Forward:); 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 3.5 bar max. differential pressure (50 psid) at 25 °C (Reverse; intermittent); 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward:); 5.5 bar max. inlet pressure (80 psi) at 23 °C; 80 psig max. inlet pressure
• Methode(n): sterile filtration: suitable
• Breite: 7.8 in.
• Nennlänge Kartusche: 10 in. (25 cm)
• device L: 37.6 cm (14.8 in.)
• device size: 10 in.
• Filterdurchm.: 4.2 in. (10.7 cm)
• filter filtration area: 1.86 m²
• Durchm. Einlassanschluss: 5/8 in.
• inlet to outlet width: 19.8 cm (7.8 in.)
• Durchm. Auslassanschluss: 5/8 in.
• Verunreinigungen: ≤0.25 EU/mL bacterial endotoxins (LAL test, aqueous extraction); <0.25 EU/mL bacterial endotoxins (LAL test, sample aqueous extraction)
• Matrix: Multilayer Durapore^®
• pore size: 0.45/0.22 μm pore size
• Blasenpunkt: ≥3450 mbar (50 psig), air with water at 23 °C
• Fitting: 1/4 in. fitting (vent/drain hose barb with double O-ring seal); (16 mm (5?8 in.) Hose Barb Inlet and Outlet)

Beschreibung

Allgemeine Beschreibung

Device Configuration: Capsule

Verpackung

Double Easy-Open bag

Angaben zur Herstellung

Sterilization Method:
3 autoclave cycles of 60min at 126°C; not in-line steam sterilizable

This product was manufactured with a Durapore^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21CFR210.3(b)(6).

Hinweis zur Analyse

Bacterial Retention: Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity: After sterilization and a controlled water flush, samples exhibited less than 500ppb TOC per USP < 643 > and less than 1.3μS/cm per USP < 645 > at 25°C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥ 1.5 L

Sonstige Hinweise

Directions for Use:

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer Wetting Instructions for Filter Units with Durapore^® Membrane user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations

Rechtliche Hinweise

ASTM is a registered trademark of American Society for Testing and Materials

Durapore is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany