KTGRA10TT1

Aervent^® 0,2 µm, Cápsula Opticap^® XL

Opticap^® XL 10, inlet connection diam. 1.5 in., pore size 0.2 μm, cartridge nominal length 10 in. (25 cm)

• Sinônimo(s): Aervent KTGR Opticap XL10 Capsule
• Código UNSPSC: 23151806
• eCl@ss: 32031690

Propriedades

• Materiais: PTFE ; polypropylene ; polypropylene housing; polypropylene support; polypropylene vent cap; silicone seal
• Nível de qualidade: 400
• esterilidade: non-sterile
• Compatibilidade de esterilização: autoclavable compatible
• linha de produto: Opticap^® XL 10
• Características: hydrophobic
• fabricante/nome comercial: Aervent^®
• Parâmetros: ≤24 mL/min nitrogen diffusion at 970 mbar (14 psig) and 23 °C (in 70/30% IPA/water); 1.0 bar max. differential pressure (15 psid) at 80 °C (Forward); 1.0 bar max. inlet pressure (15 psi) at 80 °C (Forward); 2.8 bar max. inlet pressure (40 psi) at 60 °C (Forward); 25 °C max. inlet temp.; 4.1 bar max. differential pressure (60 psid) (Reverse; intermittent); 4.1 bar max. inlet pressure (60 psi) (Reverse; Intermittent); 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward); 5.5 bar max. inlet pressure (80 psi) at 25 °C (Forward); 80 psig max. inlet pressure
• técnica(s): gas filtration: suitable
• Comprimento: 33.5 cm (13.2 in.)
• Largura: 4.2 in.
• comprimento nominal do cartucho: 10 in. (25 cm)
• Diâmetro: 10.7 cm (4.2 in.)
• área de filtração: 0.65 m²
• diâm. conexão de entrada: 1.5 in.
• L entrada para a saída: 33.5 cm (13.2 in.)
• diam. conexão de saída: 1.5 in.
• Impurezas: <0.25 EU/mL USP bacterial endotoxins (LAL test, aqueous extraction)
• extraíveis gravimétricos: ≤45 mg/cartridge
• Matriz: Aervent^®
• tamanho de poro: 0.2 μm pore size
• entrada: sample type gas
• ponto de bolha: ≥1100 mbar (16 psig), nitrogen with 70/30% IPA/water at 23 °C
• conector: 1/4 in. drain/vent hose barb (with double O-ring Seal); inlet sanitary flange; outlet sanitary flange; (38 mm (1 1/2 in.) Sanitary Flange Inlet and Outlet)

Descrição

Descrição geral

Device Configuration: Capsule

Características e benefícios

Rated for aerosol retention of a total challenge of 108–1010 plaque forming units of ΦX-174 virus particles at 85 Nm3/h (50 SCFM) per cartridge.

Embalagem

Double Easy-Open bag

Qualidade

Retains Brevundimonas diminuta liquid aerosol for 21 days at a minimum challenge of 10⁷ CFU/cm²

Ligação

Replaces: SN2M027A6

Nota de preparo

Sterilization Method
30 autoclave cycles of 30 min @ 135 °C

This product was manufactured with a PTFE membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Nota de análise

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

Gravimetric Extractables: after 24 hours in a 70/30% IPA/water mixture at controlled room temperature

HydroCorr: ≤0.75 mL/min @ 2.6 bar (38 psig) per sample

Outras notas

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer Steam Sterilization & Integrity Testing Procedures guide and first page of Visual Inspection Guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Informações legais

AERVENT is a registered trademark of Merck KGaA, Darmstadt, Germany

ASTM is a registered trademark of American Society for Testing and Materials

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Exoneração de responsabilidade

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 2014/68/EU of 15 May 2014. This product has been classified under Article 4 § 3 of the Directive 2014/68/EU. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 4 § 3 of the Directive 2014/68/EU, this product does not bear the CE mark.