918571

3D Printable Yttria-stabilized Zirconium(IV) Oxide Ink

• 同義詞: 3D printable ceramic ink, 3Y-ZrO₂ ink, YSZ ink, Yttria stabilized zirconia ink, Yttrium stabilized zirconium oxide ink
• 分類程式碼代碼: 12352119
• NACRES: NA.23

屬性

• 描述: Printing methods compatible with: Direct-Ink-Writing 3D printing
• 品質等級: 100
• 形狀: paste
• 環保替代產品特色: Design for Energy Efficiency; Learn more about the Principles of Green Chemistry.
• sustainability: Greener Alternative Product
• 濃度: 70 wt. % (Yttria stabilized zirconia)
• 顏色: white
• 粒徑: 120 nm
• 黏度: 2-25 Pa.s (25 °C at shear rate of 100 s^-1)
• 環保替代類別: Enabling,
• 儲存溫度: 2-8°C

描述

一般說明

We are committed to bringing you Greener Alternative Products, which adhere to one or more of The 12 Principles of Green Chemistry. This product has been enhanced for energy efficiency. Click here for more information.

應用

This product can be used in material extrusion 3D printing technique.

This product is a thixotropic ink based on yttria stabilized zirconia (YSZ) nanoparticles. It is suitable for various direct ink write (aka robocasting) printing technologies . Our YSZ ink has also been validated for stereolithography (SLA) 3D printing. The ink offers a stable dispersion of YSZ, high viscosity, good printability, and long shelf life. Annealed patterns provide excellent chemical resistance and high surface area. The ink is suitable for applications such as membranes, catalysis, separators and reactors.

注意

Handeling tips:

• Store in an airtight sealed container in refrigerator.
• Avoid exposure to heat.
• Add the thermal initiator (product No.479896) to 0.3wt% of the total 3Y-ZrO₂/PEGDA ink mass, and mix well before usage.

準備報告

Step-by-Step procedure for ink mixing and loading into syringe is in attached file.

Direct-Ink-Writing (DIW) Notes:

• Syringe Nozzle sizes ranging from 250 μm − 800 μm can be used.
• Initial pressure for DIW printing ranges from 12-18 psi, depending on nozzle diameter used.

Post Processing of DIW printed parts:

• Curing @ 110°C for 12-16 hours.
• Sintering using the following sequence:

Starting at RT, Ramp to 200°C for 6 hours.
Ramp to 300°C @ 1°C/min. Hold for 4 hours.
Ramp to 400°C @ 1°C/min. Hold for 2 hours.
Ramp to 800°C @ 2°C/min. Hold for 4 hours.
Ramp to 1090°C @ 2°C/min. Hold for 15 hours.
Ramp down to 50°C @ 2°C/min.

儲存和穩定性

Tighly seal remaining ink, and store in 2-8° C fridge.

安全資訊

• 象形圖: GHS05,GHS07
• 訊號詞: Danger
• 危險聲明: H315,H317,H318,H335
• 防範說明: P261 - P264 - P271 - P280 - P302 + P352 - P305 + P351 + P338
• 危險分類: Eye Dam. 1 - Skin Irrit. 2 - Skin Sens. 1 - STOT SE 3
• 標靶器官: Respiratory system
• 儲存類別代碼: 10 - Combustible liquids
• 水污染物質分類（WGK）: WGK 3