KN50A10FF1

Opticap® XL10 Polygard® CN

inlet connection diam. 3/4 in., pore size 5.0 μm, cartridge nominal length 10 in. (25 cm)

• Synonim(y): Opticap XL10 Polygard CN 5.0 μm 3/4 in. TC/TC, Opticap^® XL10 Polygard^® CN
• eCl@ss: 32031690
• UNSPSC Code: 23151806

Właściwości

• Nazwa produktu: Opticap^® XL 10 Capsule Media: Polygard^®-CN 5.0 µm Nominal, Chemistry: Polypropylene (PP)Inlet: 3/4 in. Sanitary FlangeOutlet: 3/4 in. Sanitary FlangeMax Operating Pressure: 80 psi @ 25 °C
• Quality Segment: 400
• material: polypropylene , polypropylene housing, polypropylene support, polypropylene vent cap, silicone seal
• reg. compliance: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• manufacturer/tradename: Opticap^®
• parameter: 1.0 bar max. inlet pressure (15 psi) at 80 °C, 2.75 bar max. inlet pressure (40 psi) at 60 °C, 25 °C max. inlet temp., 4.8 bar max. differential pressure (70 psid) at 20 °C, 5.5 bar max. inlet pressure (80 psi) at 25 °C, 80 psig max. inlet pressure
• L: 33.5 cm (13.2 in.)
• cartridge nominal length: 10 in. (25 cm)
• diam.: 10.7 cm (4.2 in.)
• filtration area: 0.42 m²
• inlet connection diam.: 3/4 in.
• inlet to outlet W: 33.5 cm (13.2 in.)
• outlet connection diam.: 3/4 in.
• impurities: ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction), <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• gravimetric extractables: ≤55 mg/capsule
• matrix: Polygard^®-CN
• pore size: 5.0 μm nominal pore size, 5.0 μm pore size
• input: sample type liquid
• fitting: inlet sanitary flange, 19 mm (3/4 in.) inlet/outlet sanitary flange, outlet sanitary flange

Opis

General description

Device Configuration: Capsule

Features and Benefits

Format: Single Layer

Packaging

Double Easy-Open bag

Preparation Note

Sterilization Method
3 autoclave cycles of 30 min @ 126 °C; not in-line steam sterilizable

Analysis Note

Gravimetric Extractables: after 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥5 L

Other Notes

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Legal Information

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

POLYGARD is a registered trademark of Merck KGaA, Darmstadt, Germany

Disclaimer

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.

Ta strona może zawierać tekst przetłumaczony maszynowo.