Direkt zum Inhalt
Merck

Design and in vitro evaluation of a novel vaginal drug delivery system based on gelucire.

Current drug delivery (2009-05-20)
M Patel Geeta, M Patel Madhabhai
ZUSAMMENFASSUNG

Carbamazepine indicated for the control of epilepsy, undergoes extensive hepatic first-pass metabolism after oral administration. A vaginal dosage form of carbamazepine is not commercially available. Conventional suppository having poor retention in the vaginal tract, as they are removed in a short time by the tract's self-cleansing action, having poor patient compliance. To overcome such problems, delivery system with mucoadhesive polymers polyox WSR N-60K and Ucarflock 302 that prolong drug permanence on the vaginal mucosa were developed. In the present study the suitability of gelucires to formulate vaginal pesseries was investigated. The possible modification of carbamazepine release kinetics by using gelucires blends and hydrophilic additives in the pesseries was evaluated. It was observed that among gelucire grades melting point higher than 37 degrees C, the release rate proved to be highly dependant on HLB value and matrix composition. In most of the formulations carbamazepine release occurred by disintegration and erosion of the matrices which is depending upon the vehicle employed. The aging study revealed that the formulations containing G50/13 and G50/13-G44/14 blends undergo some changes during one year of shelf aging. From the results obtained it can be concluded that different gelucire grades and their blends along with hydrophilic polymer could be successesively used to formulate prolong release carbamazepine pesseries.

MATERIALIEN
Produktnummer
Marke
Produktbeschreibung

Sigma-Aldrich
Poly(ethylenglykol), average Mn 400
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 8,000
Sigma-Aldrich
Poly(ethylenglykol), average mol wt 8,000, powder
Sigma-Aldrich
Poly(ethylenglykol), average Mn 6,000
Sigma-Aldrich
Poly(ethylenglykol), average Mn 3,350, powder
Sigma-Aldrich
Poly(ethylenoxid), average Mv 100,000 (nominal), powder
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 4,000
Sigma-Aldrich
Poly(ethylenoxid), average Mv 600,000 (nominal), powder
Sigma-Aldrich
Poly(ethylenglykol), average Mn 300
Sigma-Aldrich
Poly(ethylenglykol), average Mn 4,000, platelets
Sigma-Aldrich
Poly(ethylenglykol), average mol wt 400
Sigma-Aldrich
Poly(ethylenglykol), average Mn 20,000
Sigma-Aldrich
Kollisolv® PEG E 400
Sigma-Aldrich
Poly(ethylenglykol), 35,000
Sigma-Aldrich
Polyethylenglycol-Lösung, Hybri-Max, 50 % (w/v), average mol wt 1,450, 0.2 μm filtered, BioReagent, suitable for hybridoma
Sigma-Aldrich
Poly(ethylenoxid), average Mv ~4,000,000 (nominal), contains <1000 ppm BHT as inhibitor
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, for molecular biology, 6,000
Sigma-Aldrich
Poly(ethylenoxid), average Mv ~1,000,000 (nominal), powder
Sigma-Aldrich
Poly(ethylenoxid), average Mv 200,000 (nominal), powder
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 35,000
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 400
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 6,000
Sigma-Aldrich
Poly(ethylenoxid), average Mv 400,000 (nominal), powder
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 2,000
Sigma-Aldrich
Poly(ethylenglykol), average Mn 600, waxy solid (moist)
Sigma-Aldrich
Poly(ethylenoxid), average Mv ~300,000 (nominal), powder
Sigma-Aldrich
Poly(ethylenglykol), average mol wt 1,450
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 20,000
Sigma-Aldrich
Poly(ethylenglykol), BioUltra, 300
Sigma-Aldrich
Poly(ethylenoxid), average Mv ~900,000 (nominal), powder