KPGES006HH3

Millipore Express^® PHF, Capsule Opticap^® XL

Opticap^® XL 600, sterile, inlet connection diam. 9/16 in., cartridge nominal length 6.5 in. (16.5 cm)

• Synonyme(s) : Opticap XL 600 Millipore Express PHF Sterile 0.2 μm 9/16 in. HB/HB
• Code UNSPSC : 23151806

Propriétés

• Matériaux: polyethersulfone ; polyethylene support; polypropylene (gamma-stable); polypropylene housing; polypropylene vent cap; polysulfone ; silicone seal
• Niveau de qualité: 400
• Conformité réglementaire: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• Stérilité: irradiated; sterile
• Gamme de produits: Opticap^® XL 600
• Caractéristiques: hydrophilic
• Fabricant/nom de marque: Millipore Express^®
• Paramètres: ≤5.8 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 1000 bar max. differential pressure (15 psi) at 80 °C; 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. inlet pressure (80 psi) at 25 °C; 5500 mbar max. differential pressure (80 psi) at 25 °C; 80 psig max. inlet pressure
• Technique(s): bioburden reduction: suitable
• Longueur: 16.5 cm (6.5 in.)
• Longueur nominale des cartouches: 6.5 in. (16.5 cm)
• Diamètre: 5.6 cm (2.2 in.)
• Surface de filtration: 970 cm²
• Diam. du raccord d'entrée: 9/16 in.
• Largeur, de l'entrée à la sortie: 16.5 cm (6.5 in.)
• Diam. du raccord de sortie: 9/16 in.
• Impuretés: ≤0.25 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• Matrice: Millipore Express^® PHF
• Dimension de pores: 0.2 μm
• Raccords: 1/4 in. drain/vent hose barb (with double O-ring seal); inlet hose barb; outlet hose barb; (14 mm (9/16 in.) Hose Barb Inlet and Outlet)

Description

Description générale

Device Configuration: Capsule

Sterile capsules meet current USP and AAMI guidelines for sterility utilizing a validated sterilization cycle.

Conditionnement

Double Easy-Open bag

Autres remarques

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer wetting instructions of Filters with MILLIPORE EXPRESS^® Membrane user guide
• Storage Statement: Please refer Filters with MILLIPORE EXPRESS^® Membrane user guide
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Notes préparatoires

Sterilization Method
3 autoclave cycles of 60 min @ 123 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Remarque sur l'analyse

Bacterial Retention
Samples of membrane used in this filter were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 3.0 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥1 L

Informations légales

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Clause de non-responsabilité

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.