Cell Lysate Preparation

Often, the first step of analyzing protein expression or protein-protein interactions is to obtain a cell or tissue sample, lyse the cells, and extract proteins using extraction reagents. Total protein concentration must be determined for these cell lysates. Variables affecting each of these steps are outlined below, as each could affect the sensitivity and reproducibility of the Western blot.

Click on the symptoms to read about the possible causes and remedies:

• Total Protein Concentration Too Low
  
• Protein Concentration Too High
  
• Variability in Measured Total Protein Concentration between Replicates
  
• Non-Linear Standard Curve (for Colorimetric Assays for Total Protein)
  
• Degradation Band on Blot
  
• Bands Smeared Vertically
  
• Bands of Interest Obscured

Total Protein Concentration Too Low

Protein concentration too low as seen on Coomassie-stained membrane	Possible Cause	Remedy
	Heat degradation	Perform all lysate preparation steps at 4 °C. If sonicating, minimize total sonication time or insert breaks in between sonication pulses to minimize heat generation.
	Protein degradation	Add or increase concentration of protease and phosphatase inhibitors. Try using different inhibitor cocktails. Create lysate aliquots to minimize number of freeze-thaw cycles.
	Inadequate tissue homogenization	Increase time/power setting of sonication.
	Cell debris contamination	When pipetting supernatant following centrifugation, take care not to disturb the pellet.
	Too little tissue/too few cells	Use more tissue and/or less buffer. If using dissociated/cultured cells, make sure cell counts are accurate.
	Wrong type of lysis buffer Effect of excessively low sample pH on SDS-PAGE	Different proteins may be best visualized via Western blot using different lysis buffers. Consider the pH, buffering compound, detergents and other additives when determining the optimal buffer for a specific

Protein Concentration Too High

Possible Cause	Remedy
Insufficient buffer/tissue ratio	Use less tissue and/or more buffer. If using dissociated, cultured cells, make sure cell counts are accurate.

Variability in Measured Total Protein Concentration between Replicates

Possible Cause	Remedy
Inaccurate pipetting	Ensure accurate pipetting; use properly calibrated pipettes.
Incorrect protein standard selected (for colorimetric assays)	Switch to infrared-based protein quantitation, which directly measures amide bonds in protein chains
Time before reading absorbance too long (for colorimetric assays)	Process fewer samples at once. Switch to infrared-based protein quantitation, which is not time-dependent.
Assay incompatible with buffers used	Verify that buffers used are compatible with chosen protein quantitation assay. Use infrared-based protein quantitation, which is compatible with a wider range of buffers than colorimetric assays.
Protein concentration outside of linear dynamic range of assay	Increase or decrease lysate concentration until it is within the linear dynamic range of the selected assay. Choose an assay with a broader linear dynamic range.

Non-Linear Standard Curve (for Colorimetric Assays for Total Protein)

Possible Cause	Remedy
Pipetting error resulting in incorrect dilution of standards.	Ensure accurate pipetting; use properly-calibrated pipettes.

Degradation Band on Blot

Possible Cause	Remedy
Protein degradation due to insufficient protease inhibition	Add or increase concentration of protease and phosphatase inhibitors. Try using different inhibitor cocktails.

Bands Smeared Vertically

Possible Cause	Remedy
Protein degradation	Increase concentration of protease and/or phosphatase inhibitors during cell lysate preparation. Avoid repeated freeze/thaw cycles of cell lysate and Western blot samples.
Incompatibility between lysis buffer component and SDS Effect of interfering detergents (right lane) in SDS-PAGE	Cationic detergents in the lysis buffer will modify charge of SDS micelles, causing smearing. Remove or substitute these detergents. Nonionic detergents at high concentrations will modify SDS micelles, causing smearing. Dilute, or remove these detergents.
Excess concentration of abundant proteins, such as albumin, in the sample	First deplete the protein sample of abundant proteins, using magnetic or agarose beads designed for depletion and/or enrichment

Bands of Interest Obscured

Bands of interest on SDS-PAGE obscured by abundant proteins	Possible Cause	Remedy
	Excess concentration of abundant proteins, such as albumin, in the sample	First deplete the protein sample of abundant proteins, using magnetic or agarose beads designed for depletion and/or enrichment.