KN12A10TT1

Opticap^® XL10 Polygard^® CN

inlet connection diam. 1.5 in., pore size 1.2 μm, cartridge nominal length 10 in. (25 cm)

• 동의어(들): Opticap XL10 Polygard CN 1.2 μm 1-1/2 in. TC/TC
• UNSPSC 코드: 23151806
• eCl@ss: 32031690

속성

• material: polypropylene ; polypropylene housing; polypropylene support; polypropylene vent cap; silicone seal
• Quality Level: 400
• 규정 준수: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• 제조업체/상표: Opticap^®
• 파라미터: 1.0 bar max. inlet pressure (15 psi) at 80 °C; 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 4.8 bar max. differential pressure (70 psid) at 20 °C; 5.5 bar max. inlet pressure (80 psi) at 25 °C; 80 psig max. inlet pressure
• 길이: 33.5 cm (13.2 in.)
• 카트리지 공칭 길이: 10 in. (25 cm)
• 직경: 10.7 cm (4.2 in.)
• 여과 면적: 0.42 m²
• 입구 연결 직경: 1.5 in.
• 입구에서 출구 너비(W): 33.5 cm (13.2 in.)
• 출구 연결 직경: 1.5 in.
• 불순물: ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• 중량 추출물: ≤55 mg/capsule
• 기질: Polygard^®-CN
• 공극 크기: 1.2 μm nominal pore size; 1.2 μm pore size
• 입력: sample type liquid
• 피팅: inlet sanitary flange; 38 mm (1 1/2 in.) inlet/outlet sanitary flange; outlet sanitary flange

설명

일반 설명

Device Configuration: Capsule

특징 및 장점

Format: Single Layer

포장

Double Easy-Open bag

기타 정보

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism reduction
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer installation section of OPTICAP^® XL Capsules and OPTICAP^® XLT Capsules user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

결합

Replaces: KN1201TC1

제조 메모

Sterilization Method
3 autoclave cycles of 30 min @ 126 °C; not in-line steam sterilizable

분석 메모

Gravimetric Extractables: after 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥5 L

법적 정보

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

POLYGARD is a registered trademark of Merck KGaA, Darmstadt, Germany

면책조항

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.