콘텐츠로 건너뛰기
Merck
모든 사진(3)

문서

906808

Sigma-Aldrich

Water-soluble TPO based nanoparticle photoinitiator

contains ionic surfactant

동의어(들):

Diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide, TPO

로그인조직 및 계약 가격 보기


About This Item

UNSPSC 코드:
12352005
NACRES:
NA.25

형태

powder or solid

색상

white to off-white

SMILES string

O=P(C1=CC=CC=C1)(C(C2=C(C)C=C(C)C=C2C)=O)C3=CC=CC=C3

유사한 제품을 찾으십니까? 방문 제품 비교 안내

애플리케이션

The water-dispersible photoinitiator nanoparticle contains 10% (w/w) of the type I photoinitiator diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide (TPO). TPO is highly efficient but water-insoluble. This water-soluble TPO based photoinitiator enables rapid 3D printing of structures prepared in aqueous solutions while bringing environmental advantages by using low-energy curing systems and avoiding the need for solvents.

The extinction coefficient of the new water-dispersible nanoparticles of TPO is more than 300 times larger than the best and most used commercially available water-soluble photoinitiator, Irgacure 2959. The TPO nanoparticles absorb significantly in the range from 385 to 420 nm, making them suitable for use in commercially available, low-cost, light-emitting diode-based 3D printers and UV-curing devices.

픽토그램

Health hazardCorrosionExclamation mark

신호어

Danger

유해 및 위험 성명서

Hazard Classifications

Acute Tox. 4 Oral - Aquatic Chronic 3 - Eye Dam. 1 - Repr. 2 - Skin Irrit. 2 - Skin Sens. 1

Storage Class Code

11 - Combustible Solids

WGK

WGK 2

Flash Point (°F)

Not applicable

Flash Point (°C)

Not applicable


시험 성적서(COA)

제품의 로트/배치 번호를 입력하여 시험 성적서(COA)을 검색하십시오. 로트 및 배치 번호는 제품 라벨에 있는 ‘로트’ 또는 ‘배치’라는 용어 뒤에서 찾을 수 있습니다.

이 제품을 이미 가지고 계십니까?

문서 라이브러리에서 최근에 구매한 제품에 대한 문서를 찾아보세요.

문서 라이브러리 방문

3D printing of responsive hydrogels for drug-delivery systems
Magdassi S. et al.
Journal of 3D printing in medicine, 1(4), 219-229 (2017)
Amol A Pawar et al.
Science advances, 2(4), e1501381-e1501381 (2016-04-07)
In the absence of water-soluble photoinitiators with high absorbance in the ultraviolet (UV)-visible range, rapid three-dimensional (3D) printing of hydrogels for tissue engineering is challenging. A new approach enabling rapid 3D printing of hydrogels in aqueous solutions is presented on

문서

Water-dispersible photoinitiator nanoparticles enable novel formulations for 3D bioprinting, tissue engineering, and device manufacturing.

관련 콘텐츠

Tissue engineering fabricates tissues cultures from scaffolds, living cells, and biologically active molecules by simulating the microenvironment of the body to repair or replace damaged tissue.

조직 공학은 손상된 조직을 치료하거나 대체하기 위해 인체의 미세 환경을 시뮬레이션함으로써 지지체, 생세포, 생물학적 활성 분자로부터 조직을 배양합니다.

자사의 과학자팀은 생명 과학, 재료 과학, 화학 합성, 크로마토그래피, 분석 및 기타 많은 영역을 포함한 모든 과학 분야에 경험이 있습니다..

고객지원팀으로 연락바랍니다.