LCGL04TP6

Charged Durapore^® 0.22 µm, Optiseal^® Cartridge

OptiSeal^® 4 in., matrix Charged Durapore^®

• Sinónimos: Optiseal Charged Durapore Cartridge Filter 0.22 m
• Código UNSPSC: 23151806
• eCl@ss: 32031690

Propiedades

• Materiales: PVDF ; polypropylene ; polypropylene support; silicone seal
• Nivel de calidad: 400
• esterilidad: non-sterile
• Compatibilidad de esterilización: autoclavable compatible; steam-in-place compatible
• Línea del producto: OptiSeal^® 4 in.
• Características: hydrophilic
• fabricante / nombre comercial: OptiSeal^®
• Parámetros: ≤4 mL/min air diffusion at 2.1 bar (30 psig) and 23 °C (in water); 0.35 bar max. differential pressure (5 psid) at 121 °C (Forward); 0.35 bar max. inlet pressure (5 psi) at 121 °C (Forward); 15 L/min flow rate at 850 mbar (ΔP); 3.5 bar max. differential pressure (50 psid) at 25 °C (Reverse); 3.5 bar max. differential pressure (50 psid) at 80 °C (Forward); 3.5 bar max. inlet pressure (50 psi) at 25 °C (Reverse); 3.5 bar max. inlet pressure (50 psi) at 80 °C (Forward); 5.5 bar max. differential pressure (80 psid) at 25 °C (Forward); 5.5 bar max. inlet pressure (80 psi) at 25 °C (Forward)
• técnicas: sterile filtration: suitable
• Longitud: 4 in.
• longitud nominal del cartucho: 4 in. (10 cm)
• filtración área: 0.2 m²
• impurezas: ≤0.5 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.5 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• extraíbles gravimétricos: ≤10 mg/cartridge
• matriz: Charged Durapore^®
• tamaño de poro: 0.22 μm
• entrada: sample type liquid
• punto de burbuja: ≥2760 mbar (40 psig), air with water at 23 °C
• código del cartucho: not applicable

Descripción

Descripción general

Device Configuration: Cartridge

Envase

Double Easy-Open bag

Otras notas

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer Wetting Instructions for Filter Units with Durapore^® Membrane user guide
• Storage Statement: Store in dry location
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Nota de preparación

Sterilization Method
10 SIP cycles of 30 min @ 135 °C

This product was manufactured with a Durapore^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Nota de análisis

Bacterial Retention
Samples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

Gravimetric Extractables: after 24 hours in water at controlled room temperature

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥500 mL

Información legal

ASTM is a registered trademark of American Society for Testing and Materials

Durapore is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTISEAL is a registered trademark of Merck KGaA, Darmstadt, Germany