KPGEG1THH1

Millipore Express^® PHF, Opticap^® XLT Capsule

Opticap^® XLT 10, inlet connection diam. 5/8 in., cartridge nominal length 10 in. (25 cm)

• Sinónimos: Opticap XLT 10 Millipore Express PHF Gamma Compatible 0.2 μm 5/8 in. HB
• Código UNSPSC: 23151806

Propiedades

• Materiales: polyester support; polyethersulfone ; polypropylene (gamma-stable); polypropylene housing; polypropylene vent cap; polysulfone ; silicone seal
• Nivel de calidad: 400
• cumplimiento norm.: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
• esterilidad: irradiated; non-sterile
• Compatibilidad de esterilización: gamma compatible
• Línea del producto: Opticap^® XLT 10
• Características: gamma compatible; hydrophilic
• fabricante / nombre comercial: Millipore Express^®
• Parámetros: ≤32.7 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water); 1.0 bar max. inlet pressure (15 psi) at 80 °C; 1000 bar max. differential pressure (15 psi) at 80 °C; 2.75 bar max. inlet pressure (40 psi) at 60 °C; 25 °C max. inlet temp.; 5.5 bar max. inlet pressure (80 psi) at 25 °C; 5500 mbar max. differential pressure (80 psi) at 25 °C; 80 psig max. inlet pressure
• técnicas: bioburden reduction: suitable
• Longitud: 37.6 cm (14.8 in.)
• Anchura: 7.8 in.
• longitud nominal del cartucho: 10 in. (25 cm)
• Diámetro: 10.7 cm (4.2 in.)
• filtración área: 0.57 m²
• diám. conexión a entrada: 5/8 in.
• An entrada a salida: 19.8 cm (7.8 in.)
• diám. conexión a salida: 5/8 in.
• impurezas: ≤0.25 EU/mL bacterial endotoxins (LAL test, Aqueous extraction); <0.25 EU/mL USP bacterial endotoxins (LAL test, sample aqueous extraction)
• matriz: Millipore Express^® PHF
• tamaño de poro: 0.2 μm
• Adaptador: 1/4 in. drain/vent hose barb (with double O-ring seal); inlet hose barb; outlet hose barb; (16 mm (5?8 in.) Hose Barb Inlet and Outlet)

Descripción

Descripción general

Device Configuration: Capsule

T-line/Gauge Port: T-line

Envase

Double Easy-Open bag

Otras notas

These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.

Directions for Use

• Organism Retention: Microorganism
• Mode of Action: Filtration (size exclusion)
• Application: BioProcessing
• Intended Use: Reduction or removal of microorganism/bioburden
• Instructions for Use: Please refer wetting instructions of Filters with MILLIPORE EXPRESS^® Membrane user guide
• Storage Statement: Please refer Filters with MILLIPORE EXPRESS^® Membrane user guide
• Disposal Statement: Dispose of in accordance with applicable federal, state and local regulations.

Nota de preparación

Sterilization Method
Gamma compatible to 40 kGy; 3 autoclave cycles of 60 min @ 123 °C; not in-line steam sterilizable

This product was manufactured with a Millipore Express^® membrane which meets the criteria for a "non-fiber releasing" filter as defined in 21 CFR 210.3 (b) (6).

Nota de análisis

Bacterial Retention
Samples of membrane used in this filter were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM^® F838 methodology.

TOC/Conductivity
After sterilization and a controlled water flush of 11 L, samples exhibited less than 500 ppb TOC per USP <64> and less than 1.3 µS/cm per USP <64> at 25 °C.

Will meet the USP Oxidizable Substances Test requirements after a water flush of ≥1.5 L

Información legal

ASTM is a registered trademark of American Society for Testing and Materials

MILLIPORE EXPRESS is a registered trademark of Merck KGaA, Darmstadt, Germany

OPTICAP is a registered trademark of Merck KGaA, Darmstadt, Germany

Cláusula de descargo de responsabilidad

EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.