A new polyethylene glycol fiber prepared by coating porous zinc electrodeposited onto silver for solid-phase microextraction of styrene.

A new polyethylene glycol fiber prepared by coating porous zinc electrodeposited onto silver for solid-phase microextraction of styrene.

Analytica chimica acta (2010-03-17)

Sakchaibordee Sungkaew, Chongdee Thammakhet, Panote Thavarungkul, Proespichaya Kanatharana

PMID20226931

ABSTRACT

A new polyethylene glycol fiber was developed for solid-phase microextraction (SPME) of styrene by electrodepositing porous Zn film on Ag wire substrate followed by coating with polyethylene glycol sol-gel (Ag/Zn/PEG sol-gel fiber). The scanning electron micrographs of fibers surface revealed a highly porous structure. The extraction property of the developed fiber-to-styrene residue from polystyrene packaged food was investigated by headspace solid-phase microextraction (HS-SPME) and analyzed with a gas chromatograph coupled with flame ionization detection (GC-FID). The new Ag/Zn/PEG sol-gel fiber is simple to prepare, low cost, robust, has high thermal stability and long lifetime, up to 359 extractions. Repeatability of one fiber (n=6) was in the range of 4.7-7.5% and fiber-to-fiber reproducibility (n=4) for five concentration values were in the range 3.4-10%. This Ag/Zn/PEG sol-gel fiber was compared to two commercial SPME fibers, 75 microm carboxen/polydimethylsiloxane (CAR/PDMS) and 100 microm polydimethylsiloxane (PDMS). Under their optimum conditions, Ag/Zn/PEG sol-gel fiber showed the highest sensitivity and the lowest detection limit at 0.28+/-0.01 ng mL(-1).

MATERIALS

Product Number

Brand

Product Description

57912-U

Supelco

SPME fiber assembly Divinylbenzene/Carboxen/Polydimethylsiloxane (DVB/CAR/PDMS), for use with autosampler, needle size 23 ga, metal alloy fiber, fiber L 1 cm

11072-U

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 572, 20-45 mesh, bottle of 10 g

57914-U

Supelco

SPME fiber assembly Divinylbenzene/Carboxen/Polydimethylsiloxane (DVB/CAR/PDMS), for use with autosampler, needle size 23 ga, metal alloy fiber, fiber L 2 cm

11048-U

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 569, 20-45 mesh, bottle of 500 g

10477-U

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 1000, 40-60 mesh, bottle of 50 g

10478-U

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 1000, 60-80 mesh, bottle of 10 g

25467

Supelco

Carboxen^®-1010 PLOT Capillary GC Column, L × I.D. 30 m × 0.53 mm, average thickness 30 μm

10269

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 569, 20-45 mesh, bottle of 10 g

24246

Supelco

Carboxen^®-1010 PLOT Capillary GC Column, L × I.D. 30 m × 0.32 mm, average thickness 15 μm

25461

Supelco

Carboxen^®-1006 PLOT Capillary GC Column, L × I.D. 30 m × 0.53 mm, average thickness 30 μm

11324-U

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 564, 20-45 mesh, pack of 144 × 290 mg

10471

Supelco

Carboxen^® Adsorbent, matrix Carboxen^® 1003, 40-60 mesh, bottle of 10 g

57318

Supelco

SPME fiber assembly Carboxen/Polydimethylsiloxane (CAR/PDMS), d_f 75 μm(CAR/PDMS, for use with manual holder, needle size 24 ga

57319

Supelco

SPME fiber assembly Carboxen/Polydimethylsiloxane (CAR/PDMS), d_f 75 μm(CAR/PDMS, needle size 24 ga, for use with autosampler

24241-U

Supelco

Carboxen^®-1006 PLOT Capillary GC Column, L × I.D. 30 m × 0.32 mm, average thickness 15 μm

23446-U

Supelco

ORBO^™-93 Sorbent Tube, ORBO tube I.D. × L 6 mm × 95 mm, Bed A 180 mg, Bed B 90 mg, 60/80 mesh, pkg of 25 ea

54294-U

Supelco

Carboxen^® 572 for Tobacco Smoke, Adsorbent Bed Wt: 300 mg, cartridge size 3 mL, pkg of 50 ea

28718-U

Supelco

Tenax^® TA / Carboxen^® 1018, glass TD tube, preconditioned, O.D. × L 1/4 in. × 3 1/2 in., Sealed with (Swagelok^® End-Fittings), pkg of 10 ea

29534-U

Supelco

Carboxen^® 569, glass TD tube, fritted, O.D. × L 1/4 in. × 3 1/2 in., preconditioned, pkg of 10 ea

20355

Supelco

ORBO^™ 78 HBr on Carboxen^® 564 specially cleaned (20/45), 400/200 mg, W,W,W separators, O.D. × L 6 mm × 110 mm, pkg of 25 ea

20358

Supelco

ORBO^™ 90 Carboxen^® 564 (20/45), 160/80 mg, W,F,F separators, O.D. × L 6 mm × 75 mm, pkg of 25 ea, for analyte group MEK (methylethyl ketone)