Accéder au contenu
Merck

Degradation of sulphamethazine by means of an improved photo-Fenton process involving a hydrogen peroxide systematic dosage.

Environmental technology (2014-06-25)
Evelyn Yamal-Turbay, Lydia Pérez González, Moisès Graells, Montserrat Pérez-Moya
RÉSUMÉ

Despite being acknowledged as an emerging contaminant, sulphamethazine (SMT) degradation has received scarce attention in the advanced oxidation processes field. Thus, this work addresses the degradation of SMT in water solutions (12 L of 25mgL-1 samples) by means of a photo-Fenton process and a systematic H202 dosage protocol that enhances its performance. A conventional photo-Fenton process led to 86% mineralization after 120 min treatment when adding the Fenton reactants at once (initial concentrations were 10mgL-1 Fe(II) and 200mgL-1 H2O2). Conversely, the process achieved the total mineralization of the samples in less than 75 min when the same amount of H202 was continuously dosed according to a conveniently tuned dosage protocol. In both cases, total SMT degradation was achieved within 10 min. Hence, this work's aim is to determine the efficient dosage conditions of H2O2. The results show that a significant improvement of the photo-Fenton mineralization of SMT solutions is possible by adjusting the dosage of H2O2.

MATÉRIAUX
Référence du produit
Marque
Description du produit

Sigma-Aldrich
Peroxyde d'hydrogène solution, contains inhibitor, 30 wt. % in H2O, ACS reagent
Sigma-Aldrich
Peroxyde d'hydrogène solution, 30 % (w/w) in H2O, contains stabilizer
Sigma-Aldrich
Peroxyde d'hydrogène solution, 50 wt. % in H2O, stabilized
Sigma-Aldrich
Peroxyde d'hydrogène solution, 30% (w/w), puriss. p.a., reag. ISO, reag. Ph. Eur.
Sigma-Aldrich
Iron, ≥99%, reduced, powder (fine)
Sigma-Aldrich
Peroxyde d'hydrogène solution, contains ~200 ppm acetanilide as stabilizer, 3 wt. % in H2O
Sigma-Aldrich
Peroxyde d'hydrogène solution, contains inhibitor, 35 wt. % in H2O
Sigma-Aldrich
Peroxyde d'hydrogène solution, purum p.a., ≥35% (RT)
Sigma-Aldrich
Carbonyl iron, ≥97% Fe basis
Sigma-Aldrich
Iron, puriss. p.a., carbonyl-Iron powder, low in magnesium and manganese compounds, ≥99.5% (RT)
Sigma-Aldrich
Iron, powder, −325 mesh, 97%
Sigma-Aldrich
Iron, granular, 10-40 mesh, >99.99% trace metals basis
Millipore
Peroxyde d'hydrogène solution, 3%, suitable for microbiology
Sigma-Aldrich
Sulfamethazine, 99.0-101.0% (on dried basis)
Sigma-Aldrich
Iron, foil, thickness 0.1 mm, ≥99.9% trace metals basis
Sigma-Aldrich
Iron, chips, 99.98% trace metals basis
Sigma-Aldrich
Iron, wire, diam. 1.0 mm, ≥99.9% trace metals basis
Sigma-Aldrich
Peroxyde d'hydrogène solution, 34.5-36.5%
Supelco
Peroxyde d'hydrogène solution, ≥30%, for trace analysis
Sigma-Aldrich
Peroxyde d'hydrogène solution, contains inhibitor, 30 wt. % in H2O, meets USP testing specifications
Supelco
Peroxyde d'hydrogène solution, 30 % (w/w), for ultratrace analysis
Iron, foil, 100x100mm, thickness 0.25mm, hard, 99.5%
Sigma-Aldrich
Iron, foil, thickness 0.25 mm, ≥99.99% trace metals basis
Sigma-Aldrich
Peroxyde d'hydrogène solution, tested according to Ph. Eur.
Supelco
Sulfamethazine, VETRANAL®, analytical standard
Iron, foil, 300x300mm, thickness 0.1mm, hard, 99.5%
Iron, foil, 100x100mm, thickness 0.125mm, as rolled, 99.99+%
Iron, rod, 200mm, diameter 25mm, as drawn, 98+%
Iron, tube, 200mm, outside diameter 8.0mm, inside diameter 5mm, wall thickness 1.5mm, annealed, 99.5%
Iron, rod, 100mm, diameter 100mm, as drawn, armcO« soft ingot 99.8%