Skip to Content

Using the hemoglobin content of reticulocytes (RET-He) to evaluate anemia in patients with cancer.

Using the hemoglobin content of reticulocytes (RET-He) to evaluate anemia in patients with cancer.

American journal of clinical pathology (2014-09-23)

Ellinor I B Peerschke, Melissa S Pessin, Peter Maslak

ABSTRACT

Evaluation of anemia, particularly iron deficiency, in patients with cancer is difficult. This study examined using the hemoglobin content of reticulocytes (RET-He) to rule out iron deficiency, as defined by serum iron studies (transferrin saturation <20%, serum iron <40 μg/dL, and ferritin <100 ng/mL), in an unselected cancer patient population. Patients were entered into the study based on the existence of concurrent laboratory test requests for CBC and serum iron studies. Using a threshold of 32 pg/cell, RET-He ruled out iron deficiency with a negative predictive value (NPV) of 98.5% and 100%, respectively, in the study population (n = 209) and in a subpopulation of patients with low reticulocyte counts (n = 19). In comparison, the NPV of traditional CBC parameters (hemoglobin, <11 g/dL; mean corpuscular volume, <80 fL) was only 88.5%. These results support the use of RET-He in the evaluation of iron deficiency in a cancer care setting.

MATERIALS

Product Number

Brand

Product Description

Sigma-Aldrich

Ferritin from human liver, Type IV, 10 μg/mL

Sigma-Aldrich

Carbonyl iron, ≥97% Fe basis

Sigma-Aldrich

Iron, ≥99%, reduced, powder (fine)

Sigma-Aldrich

Iron, granular, 10-40 mesh, >99.99% trace metals basis

Sigma-Aldrich

Iron, foil, thickness 0.25 mm, ≥99.99% trace metals basis

Sigma-Aldrich

Iron, wire, diam. 1.0 mm, ≥99.9% trace metals basis

Iron, foil, light tested, 25x25mm, thickness 0.01mm, 99.85%

Iron, microfoil, disks, 10mm, thinness 0.15μm, specific density 176.7μg/cm², permanent mylar 3.5μm support, 99.99+%

Iron, rod, 100mm, diameter 19mm, as drawn, soft ingot 99.8%

Iron, rod, 1000mm, diameter 19mm, as drawn, soft ingot 99.8%

Iron, foil, 8mm disks, thickness 0.038mm, hard, 99.5%

Iron, foil, not light tested, 25x25mm, thickness 0.001mm, 99.85%

Iron, foil, not light tested, 100x100mm, thickness 0.004mm, 99.85%

Iron, foil, light tested, 25x25mm, thickness 0.075mm, as rolled, 99.99+%

Iron, foil, light tested, 100x100mm, thickness 0.05mm, hard, 99.5%

Iron, foil, 8mm disks, thickness 0.125mm, as rolled, 99.99+%

Iron, rod, 1000mm, diameter 9.5mm, as drawn, soft ingot 99.8+%

Iron, foil, 8mm disks, thickness 0.9mm, as rolled, 99.5%

Iron, foil, 25x25mm, thickness 0.125mm, hard, 99.5%

Iron, foil, not light tested, 25x25mm, thickness 0.005mm, 99.85%

Iron, rod, 200mm, diameter 6.35mm, as drawn, soft ingot 99.8%

Iron, rod, 150mm, diameter 6.0mm, as drawn, 99.99+%

Iron, rod, 100mm, diameter 12.7mm, as drawn, 98+%

Iron, foil, 100x100mm, thickness 1.0mm, as rolled, 99.5%

Iron, foil, 5m coil, thickness 0.038mm, hard, 99.5%

Iron, foil, 6mm disks, thickness 0.003mm, 99.85%

Iron, foil, 50mm disks, thickness 0.15mm, hard, 99.5%

Iron, foil, 6mm disks, thickness 0.015mm, 99.85%

Iron, foil, 5m coil, thickness 0.05mm, hard, 99.5%

Iron, foil, 6mm disks, thickness 0.025mm, as rolled, 99.99+%